Upload and Download Parameter of Lenze 8200 Vector

01 Press right arrow button

02 Press 1<->2 button             Display: 1 flashing

03 Press right arrow button               Display: USER ^0001000 flashing

04 Press up arrow button                  Display: ALL ^0002000 flashing

05 Press 1<->2 button             Display: 0 ^0001000 flashing

06 Press up arrow button                  Display: 0 ^0002000 flashing

07 Press right arrow button               Display: 0 flashing ^0002000

08 For Upload:

    
Press 20times up arrow button    Display: 20 flashing ^0002000

     
For Download:

     
Press 10times up arrow button    Display: 10 flashing ^0001000

09 Press Enter button                         Display: for Upload: Save

                                                                          for Download: Load

10 Restart the drive

Now the follow steps to identify the right motor

• Make conveyor belt 1 in operating panel
• After down loading follow these steps:

01 Press Stop button

02 According steps 1 to 5 Up/Download (complete steps 1 to 5 up/down load)

03 Press up arrow button until u gets the parameter 148    Display: 0 ^0148000 flashing

04 Press right arrow button               Display: 0 flashing ^0148000

05 Press up arrow button                  Display: 1 flashing ^0148000

06 Press Enter button

07 Start the belt from the DCP-2 panel

08 Press Run button                           Display: The Imp Symbol goes off for ~ 10sec

09 Restart the drive

10 Steps 1-3 again but go to parameter 015 and change from 50 to 87Hz by pressing right

      arrow

11 Restart again

Programming Lenze Drive 9300 Series Main, Aux and Pick Up G2G3G4 by Laptop

	TO TAKE BACKUP FROM LENZE DRIVE TO LAPTOP
1	Connect LECOM to drive and RS232 cable to Laptop
2	Connect 24 Vdc supply to connector no. 39(-) and 59(+)
3	Open GDC ( Global Drive Controller) software from desktop
4	It starts searching, 'IF not' Press F4 and then F2, select search
5	Automatically reading parameter from drive
6	Short commissioning 93XX window open
7	Select code list
8	Select Drive parameters and select write all parameters set to "File"
9	Type file name e.g. 05ngr1.GDC and check the saving path.
10	Press OK
11	Select F4 before quit the program GDC
12	Please check saved file in saving path positon.
	TO TAKE BACKUP OF LENZE DRIVE AT FOLDER A AND B
1	Put jumper in 2 and 3 then connect LECOM
2	Follow above 1 to 12 steps
	TO TAKE BACKUP FROM LAPTOP TO LENZE DRIVE
1	Connect LECOM to drive and RS232 cable to Laptop
2	Connect 24 Vdc supply to connector no. 39(-) and 59(+)
3	Open GDC ( Global Drive Controller) software from desktop
4	It starts searching, 'IF not' Press F4 and then F2, select search
5	Automatically reading parameter from drive
6	Short commissioning 93XX window open
7	Select Drive parameters and select read all parameter set from file
8	Read parameter set from file window open, select the file to be load, press OK
9	GDC warning window open, Press Yes, Code list display on window
10	Select drive parameters and select write all parameter set to drive
11	Warning parameter set transfer window open, Press OK
12	Transfer variant selection-parameter set to drive window open
	Press exchange unit
13	Parametersatztransfer window open
14	Start writing parameter to drive, after finish
15	Press F4
16	Close GDC
17	OFF/ON the power of drive
	UPLOAD AND DOWNLOAD PARAMETER FROM 2 IN 1 PLC TO PC
1	Connect 24 VDC supply to connector no. 3(-) and 2(+)
2	Connect cable to RS232 and PC
3	Choose program PVI
4	Transfer pvi file
5	Select execute.
6	Downloading starts
7	Finish successfully
8	Path D:mullermartini\_mm software 2009\2 in 1\2 in 1 transfer